Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
Almost everyone may have their private conception involving How to Install a Bathtub.
Installing a bathtub isn't exactly rocket science, yet it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a new one is likewise a moderately hard task. If the old tub is readily accessible, the job can move quickly; if you have to open up a wall to get rid of the old tub and place the new tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will require an assistant to vacate the old bathtub as well as set in the brand-new one. Make certain you have actually qualified on your own for the job and fit trying it. Instead of working with a professional to take over a halfway-completed task, it is much better to consider using one before you start. Opportunities are you may need a specialist plumber to make tube links.
This write-up will certainly assist you install a new bath tub in your washroom if you have actually already acquired a new tub and don't require to alter the arrangement of your previous water pipelines.
Your tools and material list need to comprise the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making certain that the washers remain in location in between the tap and the sink. Protect the tap in position with the producer given backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply as well as examine all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the bath tub and also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub should wait until the bathtub has been used a minimum of once as this will settle it into its final position.
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, bring about difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are marketed in tubes as well as cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealer can crack rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that information was mandatory. So long as you appreciated our blog entry please remember to pass it around. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Explore Now Report this page